防水防油整理剂AG-E 7500B
AG-E 7500B 由旭硝子株式会社独自开发的含氟防水防油加工剂,赋予各种纤维以优异的防水防油特性。
一、物化性能
外观 乳白色乳液
PH 酸性
比重(20℃) 1.0
含固量 22%
离子性 弱阳离子
溶解性 易稀释分散于水中
二、使用方法
AG- E7500B通常采用浸轧法加工使用，标准处方的使用浓度根据对象纤维材料/纤维以及使用目的而有所不同.一般情况下使用浓度为：
AG- E7500B 15-40g/L
干燥条件 100-120℃ 1-3分钟
焙烘条件 150-170℃ 1-3分钟
产品性能
1.赋予各种纤维以优异的防水防油特性；
2.赋予较为柔软的手感；
3.稳定性佳,受前道工序的残留物染料及拼用助剂影响小；
产品性能
1.AG-E7500会有对加工布料的各种特性(强度/柔软性,抗劈裂,带电性等),色调,坚牢度带来影响的情况发生.
2.可以拼用抗静电剂/柔软剂/渗透剂等其它助剂,请事先充分确认其相容性及对防水防油性的影响.调液时,请先将各种加工助剂至少稀释2-3倍以上后再混合.
3.稀释本品时请用40℃以下的水.加工中请将工作液温度控制在40℃以下.
4.工作液的PH值请调节在7以下弱酸性,在强酸性和碱性的条件下会影响防水防油性能.
贮 存
1.本产品请在5℃-35℃的范围内，避免直射阳光，密闭保存。在冷冻和长期高温下的保存，有可能对品质产生不好的影响。
2.将本产品从容器中取出时，请先搅拌均匀。
3.请阅读MSDS并正确使用本产品。
HOLPOSON® AG-E 7500B
AG-E 7500B is a fluorinated waterproof and oil-proof agent developed independently by Asahi Nitz Co., Ltd., which endows various kinds of fibers with excellent waterproof and oil-proof properties.
Physical & chemical properties:
Appearance: Milky white emulsion
pH: Acidic
Specific gravity (20 ℃): 1.0
Solid content: 22%
Ionicity: Weak cationic
Solubility: Easily dilutable and dispersable in water
Usage:
AG-E 7500B is usually used with padding method, and the concentration of the standard recipe varies according to the target fiber material/fiber and the purpose. In general, the concentration is:
AG- E7500B: 15-40g/L
Drying condition: 100-120 ℃ for 1-3 minutes
Baking condition: 150-170 ℃ for 1-3 minutes
Characteristics:
1. Endows all kinds of fibers with excellent waterproof and oil resistant properties;
2. Gives textiles soft hand feel;
3. It has good stability and is little affected by the residual dyes and mix-used agents of in the previous process;
Attentions:
1. AG-E7500B will affect the properties (strength/softness, cleavage resistance, electrification, etc.) of processed fabric, color tone and fastness.
2. Other auxiliaries such as antistatic agent/softener/penetrant can be mix-used. Please fully confirm their compatibility and influence on water and oil resistance in advance. When mixing, please dilute various processing auxiliaries at least 2-3 times before mixing.
3. Please use water below 40 ℃ when diluting the product. Please control the working solution temperature below 40 ℃ during processing.
4. Please adjust the pH value of the working solution below 7 in weak acidity. Waterproof and oil-proof performance will be impacted under the condition of strong acidity and alkalinity.
Storage:
1. Please store the product in temperature range of 5 ℃ - 35 ℃, avoid direct sunlight, and keep it sealed. It is possible to have a bad effect on the quality if it is preserved in freezing and high temperature for a long time.
2. When taking the product out of the container, please mix it evenly first.
3. Please read MSDS and use this product correctly.
